Almost complete Calypso pics inside!!!

[EHA Racing]

This project is coming to an end with only a day and a half of work left on it.
All that's left is to assemble and install the rear diff, anti roll bar and nitrous plate. The car runs great and looks great and we are just extatic about the project overall.
Here are some of the final assembly pics.

 

[1990_LX]

Nice man!! On a side note, why isn't that damn boat shrink wrapped or at least all covered?? LOL

 

[BionicBooger]

It should be, but its not our boat LOL

 

[1990_LX]

It should be, but its not our boat LOL

Oh, well then it's not your problem. Haha

 

[marguerite66]

Looks awesome! Great job guys!!

 

[Timspony]

Looking good! ...How does the car handle in the snow?

 

[EHA Racing]

LOL. We drove it out of the shop so we could move some things around then right back in. But it did OK haha.

 

[sbeachstang]

Can't wait to see it run, looks bad ass!

 

[BionicBooger]

Can't wait to see it run, looks bad ass!

Thanks Scott!

 

[94Gt5.0]

Looks good man! Seeing your setup is pushing me closer and closer to ditching my EFI system and going carb'd..

 

[EHA Racing]

Looks good man! Seeing your setup is pushing me closer and closer to ditching my EFI system and going carb'd..

You should see the throttle response of that little bastard. Unreal!!

 

[94Gt5.0]

You should see the throttle response of that little bastard. Unreal!!

Whats the setup on it??

 

[EHA Racing]

Whats the setup on it??

306, TRW flat tops, ported TFS heads, 2.055/1.60 valves, port matched super vic. matched to a 1262R gasket, 232/240 dur. @ .05", .565 /.577 hyd. roller cam and pro-systems custom carb 730 cfm with annular boosters.
Hoping for 11.70's on motor with a 4,500 stall trans brake c-4, 3.90 gears and 275/60/15 ET Street Radials

 

[94Gt5.0]

306, TRW flat tops, ported TFS heads, 2.055/1.60 valves, port matched super vic. matched to a 1262R gasket, 232/240 dur. @ .05", .565 /.577 hyd. roller cam and pro-systems custom carb 730 cfm with annular boosters.
Hoping for 11.70's on motor with a 4,500 stall trans brake c-4, 3.90 gears and 275/60/15 ET Street Radials

Nice, it shouldnt have much trouble hitting that goal as long as the 60' is there! What carb/intake setup would you suggest for my car? Its a 10.25:1 331 with Edlebrock 1.90/1.60's etc etc.

 

[EHA Racing]

Nice, it shouldnt have much trouble hitting that goal as long as the 60' is there! What carb/intake setup would you suggest for my car? Its a 10.25:1 331 with Edlebrock 1.90/1.60's etc etc.

I think a vic jr or Parker would be plenty. As ar as the carb I will only go to Patrick at Pro-systems. he designs the carb specifically for your engine and driving goals and they come with a complete build and flow sheet. He is usually within 2 jet sizes of perfect a/f ratio. They are running $702 shipped to your door and a brand new off the shelf holley DP is the same price.
Shanes car fires with a 1/2 pump of the gas and a 1/2 trun of the crank.

BTW, the only reason we are running a super vic is because we bought the heads and intake combo used off NMRA and I didn't want to separate them.

 

[94Gt5.0]

I think a vic jr or Parker would be plenty. As ar as the carb I will only go to Patrick at Pro-systems. he designs the carb specifically for your engine and driving goals and they come with a complete build and flow sheet. He is usually within 2 jet sizes of perfect a/f ratio. They are running $702 shipped to your door and a brand new off the shelf holley DP is the same price.
Shanes car fires with a 1/2 pump of the gas and a 1/2 trun of the crank.

BTW, the only reason we are running a super vic is because we bought the heads and intake combo used off NMRA and I didn't want to separate them.

Ok thanks for the advice man. Its been awhile since Ive done the carb thing lol.

 

[EHA Racing]

No prob and if you need any help just let me know!!

 

[jmiller]

Wow... Looks great, guys. Snot Rockets FTW!!

 

[stangman1995gt]

Wow, looking great!! Can not wait to see it run!!!

 

[TBapp3]

AWESOME!